Question 1
Highly alloyed tool steels are tempered in the range of ______
A. 100⁰C – 190⁰C
B. 180⁰C – 300⁰C
C. 450⁰C – 620⁰C
D. 500⁰C – 600⁰C
View Answer
Answer: Option D
Explanation:
The tempering temperature is decided based on the type of steel. Highly alloyed tool steels are tempered in the range of 500⁰C – 600⁰C. Low alloy steels are tempered above 400⁰C to get a good combination of strength and ductility. Spring steels are tempered between 300⁰C – 400⁰C.
Question 2
Increase in the tempering temperature ______
A. increases hardness
B. increases ductility
C. decreases conductivity
D. increases toughness
View Answer
Answer: Option D
Explanation:
It is observed that the increase in the tempering temperature decreases the hardness and internal stresses while increases the toughness. But after a particular temperature, there is no significant change in hardness and toughness.
Question 3
Martensite obtained after hardening is extremely _______
A. hard
B. ductile
C. brittle
D. soft
View Answer
Answer: Option C
Explanation:
The hardened steel is not readily suitable for engineering applications. It possesses few drawbacks, which are as follows:• martensite obtained after hardening is extremely brittle and will result in failure of engineering components by cracking• Formation of martensite from austenite by quenching produces high internal stresses in the hardened steel.
Question 4
Normalizing is used for _____
A. alloy steels
B. high carbon steels
C. tool steels
D. aluminium alloys
View Answer
Answer: Option B
Explanation:
Normalizing is used for high-carbon (hypereutectoid) steels to eliminate the cementite network that may develop upon slow cooling in the temperature range from point Acm (upper critical temperature for cementite) to point A1 (lower critical point temperature).
Question 5
Normalizing takes less time than that for annealing.
A. TRUE
B. FALSE
View Answer
Answer: Option A
Explanation:
The properties of normalized components are not much different from those of annealed components. However, normalizing takes less time and is more convenient and economical than annealing and hence is a more common heat treatment in industries.
Question 6
Perlite formed during normalising is coarse in nature.
A. TRUE
B. FALSE
View Answer
Answer: Option B
Explanation:
Pearlite formed during normalizing is fine and usually appears unresolved with an optical microscope. Whereas, pearlite during annealing is coarse and usually gets resolved by the optical microscope.
Question 7
Structures obtained after hardening consists of _______
A. martensite
B. cementite
C. perlite
D. carbon
View Answer
Answer: Option A
Explanation:
Structures obtained after hardening consists of martensite and retained austenite. Both these phases are metastable and will change to stable phases with time which subsequently results in a change in dimensions and properties of the steel in service.
Question 8
Tempering is achieved by heating hardened steel to a temperature in the range of ______
A. 100⁰C – 150⁰C
B. 100⁰C – 680⁰C
C. 200⁰C – 375⁰C
D. 300⁰C – 835⁰C
View Answer
Answer: Option B
Explanation:
Tempering is achieved by heating hardened steel to a temperature below lower critical temperature, which is in the range of 100⁰C – 680⁰C, hold the component at this temperature for a soaking period of 1 to 2 hours (can be increases up to 4 hours for large sections and alloy steels), and subsequently cooling back to room temperature.
Question 9
In normalizing of hypoeutectoid steel, the component is heated to a temperature above _____
A. 535⁰C
B. 610⁰C
C. 800⁰C
D. 910⁰C
View Answer
Answer: Option D
Explanation:
Normalizing process consists of three steps. The first step involves heating the steel component above the 910⁰C temperature for hypoeutectoid steels and above Acm (upper critical temperature for cementite) temperature for hypereutectoid steels by 30⁰C to 50⁰C.
Question 10
In normalizing, components are cooled _____
A. using water
B. using oil
C. in still air
D. in furnace
View Answer
Answer: Option C
Explanation:
The final step in normalizing involves cooling the hot steel component to room temperature in still air. Due to air cooling, normalized components show a slightly different structure and properties than annealed components.
Question 11
In normalizing, grain size distribution ______
A. is uniform
B. is less uniform
C. varies directly with temperature
D. varies with time
View Answer
Answer: Option B
Explanation:
If we compare annealing and normalizing, the following point can be made:In annealing,• Grain size distribution is more uniform• Internal stresses are least• Less hardness, tensile strength and toughnessIn normalizing,• Grain size distribution is slightly less uniform• Internal stresses are slightly more• Slightly more hardness, tensile strength and toughness.